These robust hot dip galvanized cable drum stands are designed to be placed on the ground or on the back of a tray-back truck and are provided with container lock mounting points. All spindle hardware is zinc plated and gold passivated, the hydraulic disc brake is manufactured from stainless steel and the power pack enclosure is powdercoated. They are also provided with lifting lugs, one on each corner. In addition to this, there are lifting points provided on each end of the spindle assembly for lifting the drum and spindle out of the stand. The spindle is manufactured from special high tensile hollow section and can be lifted by one person.

6 Tonne skid-mount cable drum stand complete with a line brake (pay out) capacity of 200kg at 1000mm diameter. As an optional extra, these drum stands may be supplied with an integrated diesel/hydraulic power unit and drum drive with a line pull (recovery) capacity of 500kg at 1000mm diameter.

Specification

Maximum Drum Mass: 6000kg
Maximum Drum Diameter: 2800mm
Maximum Drum Width : 1500mm
Maximum line pulls: 500kg at 1000mm dia. 1000kg at 1000mm dia.
Spindle diameter: 95mm

Please note the spindle diameter quoted is a special lightweight spindle with 95mm outside diameter. If 90mm is required, this will be a solid spindle in order to carry the 6 tonne drum weight. A solid spindle will be much heavier than the hollow one we normally provide and it will be a 2 or 3 man operation to lift the spindle. For this reason, most authorities prefer lightweight spindles.

Parts Books & Operating Instructions

The equipment is supplied with one copy of an operation manual which includes operating instructions, safety information, major assembly drawings, hydraulic and electrical schematics (if applicable), etc. Additional copies are available upon request at nominal cost.

Change in Specification

Design and improvement of products is a continuous process. We, therefore, reserve the right to make design improvements differing from this specification after receipt of an order. However, any major changes will only be made with the approval of the customer or its’ representatives.

Warranty

12 months parts and labour in accordance with guarantee and sales conditions.

Options

Option 1
(view image)     
Single 6 Tonne drum stand assembly
Including
– Stainless steel disc brake assembly, 200 kg tension.
– 95mm spindle assembly,
Excluding
– Diesel/hydraulic power pack
– 500 kg line pull drum rotator assembly.

Option 2
(view image)     
Single 6 Tonne drum stand assembly
Including
– Stainless steel disc brake assembly, 200 kg tension.
– 95mm spindle assembly,
– Integral diesel/hydraulic power pack and valving
– 500 kg line pull drum rotator assembly.

Option 3
(view image)     
Single 6 Tonne drum stand assembly
Including
– Stainless steel disc brake assembly, 200 kg tension.
– 95mm spindle assembly,
– Integral /diesel/hydraulic power pack and valving
– 500 kg line pull drum rotator assembly.
– Fairlead control system.
Excluding
– Fairlead framework and mechanism
Suitable for use with intermediate frame and fairlead system as per option 8.
Excluding
– Diesel/hydraulic power pack

Option 4
(view image)     
Single 6 Tonne drum stand assembly
Including
– Stainless steel disc brake assembly, 200 kg tension.
– 95mm spindle assembly,
– 500 kg line pull drum rotator assembly.
– Hydraulic control valving
Excluding
– Diesel/hydraulic power pack
Suitable for use with truck PTO drive or remote diesel/hydraulic power unit as per Option 5.

Option 5
(view image)     
Manufacture remote skid mounted diesel/hydraulic power unit suitable to drive ONE Single 6 Tonne drum stand assembly. Typically as per option 4.
– Excludes hydraulic control valving
– Includes hose reels

Option 6     
Manufacture one intermediate subframe to support TWO non powered drum stands Typically option 1.
(Excluding drum stands )

Option 7     
Manufacture one intermediate subframe to support TWO powered drum stands. Typically supporting one unit as per option 3 and one unit as per option 4.
(Excluding drum stands)

Option 8     
Manufacture one intermediate subframe to support TWO powered drum stands complete with fairlead assembly. Typically one unit as per option 3 and one unit as per option 4.
(Excluding drum stands)

Option 9
(view image)     
Manufacture one intermediate subframe to support THREE non powered drum stands. Typically three units as per option 1. (Excluding drum stands)

Option 10     
Manufacture heavy-duty overhead support roller. Maximum cable capacity 100mm diameter.

Option 11     
Manufacture light duty overhead support roller. Maximum cable capacity 40mm diameter.

Option 12     
Spreader bar and chain assembly for lifting drums in and out of stand

Option 13     
Additional 3000 kg spindle

Option 14     
Complete 3000 kg spindle and brake assembly

Option 15     
Hydraulic hand-pump assembly for greater brake control.

Option 16     
1000 kg line pull drum rotator assembly.

Option 17
(view image)     
Upgrade stainless steel brake spindle assembly from 200 kg tension to 900 kg tension

Option 18     
Upgrade 500 kg line pull (rotator) to 1000 kg line pull.

Option 19
(view image)     
Intermediate Frame Lifting Attachment

Option 20
(view image)     
3mm Aluminium checker plate flooring put on the base of Drum Stands – Options 1, 2, 3 and 4

Option 21
(view image)     
Set of fold-down decking and suitable barrier system to suit 3-Drum intermediate stand – Option No. 9

Option 22     
3mm checker plate flooring for 3-Drum intermediate stand – Option No. 9

Option 23
(view image)     
Cable Bender:
The cable bender has been designed to straighten the ends of heavy cables before putting them through the cable pusher or during the joining process. It is of lightweight aluminium construction, hand-pump operated by a single acting hydraulic cylinder. The cable bender can handle cable from 50-160mm diameter.